[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

update



Hi!

After some troubles with the board and our network, I decided to upgrate my
board (to release 1.0.2)
To avoid networktroubles I connected the board via a cross over ethernet cable. 
I changed the IP of my PC to 192.36.253.81 (netmask: 255.255.255.0,  gateway
192.1.1.1) to be at the same network segment.
I followed the instructions of  "how to install the DevBoard Software",
"how to usermkprod" and "how to use boot_elinux"
"boot_elinux -f" did not terminate.
*) I  runned ./init_env
*) I  ceated an image
*) I _was_ in the boot-mode.
*) and its unpossible, that I have network troubles, because - as I said bevor -
  I'm connected directly
*) After rebooting (normal output so far) there are no further outputs at COM2. 
*) I can ping the port, so the ethernet cable should be ok

? any ideas ?

NKrug

***************************************************************************************
attachment. sermon output:

Sniffing /dev/ttyS1 at 115200 Baud
Probing flash...
Flash: 16Mb TB.
Flash: No flash or unsupported manufacturer.
ROM fs in RAM, size 1381504 bytes
Linux/CRIS-NOMMU port (c) 1999 Axis Communications AB
Flat model support (C) 1998 Kenneth Albanowski, D. Jeff Dionne, TSHG Ltd.
Entering paging_init(), mem start 0x401e8cb0, end 0x40800000
Entering trap_init(), mem start 0x40206000
Initializing interrupts
sched_init
DS1302 RTC found.
SDA, SCL, RST on PB0, PB1, PB2
rtc_time        : 00:00:80
rtc_date        : 2000-01-01
rtc: sec 0x80 min 0x0 hour 0x0 day 0x1 mon 0x1 year 0x0
Enabling watchdog...
console_init 0x40206000
kmalloc_init 0x40206000
Calibrating delay loop... 99.58 BogoMIPS
Entering mem_init(40206000,40800000)
Mem_init: start=40206000, end=40800000
Memory: 6120k/7798k available (396k kernel code, 1676k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
Linux version 2.0.38 (amir@xxxxxxx.2) #1 Thu Jun 8 14:50
:34 CEST 2000
Starting init thread...
Starting kswapd v 1.7
I2C driver v2.0, (c) 1999 Axis Communications AB
Etrax/100 serial driver v2.0, (c) 2000 Axis Communications AB
ttyS0 at 0xb0000060 is a builtin UART with DMA
ttyS1 at 0xb0000068 is a builtin UART with DMA
ttyS2 at 0xb0000070 is a builtin UART with DMA
ttyS3 at 0xb0000078 is a builtin UART with DMA
Etrax/100 DMA parallel port driver v0.3, (c) 2000 Axis Communications ABInitializing parallel port registers... par0 par1  done
par0 rxint, status: 0x3F0100FF 0xFF ctrl: 0x00000000 config: 0x01E00069
par1 rxint, status: 0x3F010000 0x00 ctrl: 0x00000000 config: 0x01E00069
Etrax general-port I/O driver v2.0, (c) 1999 Axis Communications AB
EEPROM char device v0.3, (c) 2000 Axis Communications AB
e100eeprom: Assuming i2c compatible 2Kb eeprom.
Ramdisk driver initialized : 16 ramdisks of 4096K size
KROM block (c) 1998 D Jeff Dionne, SHG Ltd [1350k] at 40097830
Flash/ROM block device v2.1, (c) 1999 Axis Communications AB
Flash/ROM char device v2.1, (c) 1999 Axis Communications AB
Checking flash partitions:
  /dev/flash0 at 0x80000000, size 0x10000
  No partitiontable recognized. Using default flash1 and flash2.
  /dev/flash1 at 0x80010000, size 0x1a0000
  /dev/flash2 at 0x801b0000, size 0x50000
Etrax/100 10/100MBit ethernet driver v1.3, (c) 2000 Axis Communications A
B
eth0 initialized
eth0: changed MAC to 00:40:8C:CD:00:00
JFFS (Flash Shortcut) version 1.0, (C) 1999, 2000  Axis Communications AB
VFS: Mounted root (romfs filesystem) readonly.
mounting proc
Starting ping_ipset thread
Starting init...
Init starts up...
Doing factory default!
Ok.
Mounting /etc
JFFS: Trying to mount device 3c:12.
JFFS: Successfully mounted device 3c:12.
Mounted /dev/flash2 on /mnt/flash ok.
mactool: /etc/network/mac.conf is rewritten with serial number as MAC add
ress.
Setting up eth0 with ip 192.36.253.80 and mac 00:40:8c:18:10:91
change IP to 0x50fd24c0
eth0: changed MAC to 00:40:8C:18:10:91
Setting up lo with ip 127.0.0.1
change IP to 0x100007f
Default gateway is 192.1.1.1
Hostname is AxisProduct
Unpacking 512 kbyte ramdisk
Mounting ramdisk on /tmp
Mounted /dev/ram0 on /tmp ok.
kfree of non-kmalloced memory: 40273d98, next= 40247000, order=1 (pid 9)Stack dump [0x402fbd2a]:
sp + 0: 0x4006742c
sp + 4: 0x40273d90
sp + 8: 0x4000d5a8
sp + 12: 0x00000009
sp + 16: 0x00000000
sp + 20: 0x00000020
sp + 24: 0x40222e98
sp + 28: 0x40252938
sp + 32: 0x402529b8
sp + 36: 0x4024d000
sp + 40: 0x4000bfac
sp + 44: 0x00000002
sp + 48: 0x40236e38
sp + 52: 0x40222e98
sp + 56: 0x40236c0c
sp + 60: 0x40009b54
Weird, init caught unknown child die. Oh well.
Telnetd starting, using port 23.
  using /bin/sash as shell.
boa: servername set to 192.36.253.80.
boa[22]: starting server
Weird, init caught unknown child die. Oh well.
sersrvd by Johan.Adolfsson@xxxxxxx.com
$Revision: 1.8 $
Reading configfile: ../etc/sersrvd.conf fd=5
Found group: COM1
Added config: COM1
Config Device to /dev/ttyS0
Config Mode to AUTO_CONNECT (OFF, COMMAND_MODE, AUTO_CONNECT)
Config Baudrate to 115200
Config Datasize to 8 (7, 8)
Config Stopbits to 1 (1, 2)
Config Parity to NONE (NONE, ODD, EVEN, (MARK, SPACE)?)
Config Handshake RTS/CTS to NO (NO, YES)
Config Handshake XON/XOFF to NO (NO, YES, ROBUST)
Config Connect to to
Config Listener port to 4000
Config Timeout to 0
Config Telnet options to YES (NO, YES)
Config Echo COMMAND_MODE port side to YES
Config Echo COMMAND_MODE network side to YES
Found group: COM2
Added config: COM2
Start from beginning!
Config Device to /dev/ttyS2
Config Mode to AUTO_CONNECT (OFF, COMMAND_MODE, AUTO_CONNECT)
Config Baudrate to 115200
Config Datasize to 8 (7, 8)
Config Stopbits to 1 (1, 2)
Config Parity to NONE (NONE, ODD, EVEN, (MARK, SPACE)?)
Config Handshake RTS/CTS to NO (NO, YES)
Config Handshake XON/XOFF to NO (NO, YES, ROBUST)
Config Connect to to localhost:4000
Config Listener port to 4001
Config Timeout to 0
Config Telnet options to YES (NO, YES)
Found group: COM422
Added config: COM422
Start from beginning!
Config Device to /dev/ttyS3
Config Mode to AUTO_CONNECT (OFF, COMMAND_MODE, AUTO_CONNECT)
Config Baudrate to 115200
Config Datasize to 8 (7, 8)
Config Stopbits to 1 (1, 2)
Config Parity to NONE (NONE, ODD, EVEN, (MARK, SPACE)?)
Config Handshake RTS/CTS to NO (NO, YES)
Found group: COMDBG
Added config: COMDBG
Start from beginning!
Config Device to /dev/ttyS1
Config Mode to AUTO_CONNECT (OFF, COMMAND_MODE, AUTO_CONNECT)
Config Baudrate to 115200
Config Datasize to 8 (7, 8)
Config Stopbits to 1 (1, 2)
Config Parity to NONE (NONE, ODD, EVEN, (MARK, SPACE)?)
Config Handshake RTS/CTS to NO (NO, YES)
Config Handshake XON/XOFF to NO (NO, YES, ROBUST)
Config Connect to to
Config Listener port to 4003
Config Timeout to 0
Config Telnet options to YES (NO, YES)
set_port_Speed: 115200 4098
set_port_Speed: 115200 4098
set_port_Speed: 115200 4098
set_port_Speed: 115200 4098
sftpd[23]: sftpd $Revision: 1.52 $ starting up
sftpd[23]: sftpd.conf not found