[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

please help me wirh this TCP/IP problem



sir 

i am unable to ping into the board but i can enter the
board through serial port.

previously i could able to ping into the board with
the same network settings.
if anybody can help me wheteher is it any hardware
problem in the board ......why am i not able to ping
into the board now when i could able to do it
previously. This is the output from the reset i have
doubt on....mainly on STOCADDRT .....what actually it
means.

Setting up eth0 with ip 131.91.82.156 and mac
00:40:8c:46:70:3e
change IP to 0x9c525b83
eth0: changed MAC to 00:40:8C:46:70:3E
route: netmask doesn't match route address
Setting up lo with ip 127.0.0.1
change IP to 0x100007f
Default gateway is 131.91.80.1
SIOCADDRT: Network is unreachable 
Hostname is "AxisProduct"

the resetting of the board gives the complete output
as below.Probing flash...
Flash: 16Mb TB
Flash: Unknown device
ROM fs in RAM, size 1788816 bytes
Linux/CRIS-NOMMU port, Copyright (c) 1999, 2000 Axis
Communications AB
Flat model support, Copyright (c) 1998 Kenneth
Albanowski, D. Jeff Dionne, TSHG Ltd.
Entering paging_init(), mem start 0x4024ddb0, end
0x40800000
Entering trap_init(), mem start 0x4026b000
Initializing interrupts
sched_init
DS1302 RTC found.
SDA, SCL, RST on PB0, PB1, PB2
rtc_time	: 00:00:80
rtc_date	: 2000-01-01
rtc: sec 0x80 min 0x0 hour 0x0 day 0x1 mon 0x1 year
0x0
Enabling watchdog...
console_init 0x4026b000
kmalloc_init 0x4026b000
Calibrating delay loop... 99.58 BogoMIPS
Entering mem_init(4026b000,40800000)
Mem_init: start=4026b000, end=40800000
Memory: 5716k/7793k available (400k kernel code, 2076k
data)
Swansea University Computer Society NET3.035 for Linux
2.0
IP Protocols: IGMP, ICMP, UDP, TCP
Linux version 2.0.38 (root@xxxxxxx.2)
#1 Sun Feb 4 15:59:35 EST 2001
Starting init thread...
Starting kswapd v 1.7 
I2C driver v2.0, (c) 1999 Axis Communications AB
Etrax/100 serial driver v2.0, (c) 2000 Axis
Communications AB
ttyS0 at 0xb0000060 is a builtin UART with DMA
ttyS1 at 0xb0000068 is a builtin UART with DMA
ttyS2 at 0xb0000070 is a builtin UART with DMA
ttyS3 at 0xb0000078 is a builtin UART with DMA
Etrax/100 DMA parallel port driver v1.0, (c) 2000 Axis
Communications AB
Initializing parallel port registers... par0 par1 
done 
par0 rxint, status: 0x3F0100FF 0xFF ctrl: 0x00000000
config: 0x01E00069
par1 rxint, status: 0x3F010000 0x00 ctrl: 0x00000000
config: 0x01E00069
Etrax general-port I/O driver v2.0, (c) 1999 Axis
Communications AB
EEPROM char device v0.3, (c) 2000 Axis Communications
AB
e100eeprom: Assuming i2c compatible 2Kb eeprom.
Ramdisk driver initialized : 16 ramdisks of 4096K size
KROM block (c) 1998 D Jeff Dionne, SHG Ltd [1747k] at
40099220
Flash/ROM block device v2.1, (c) 1999 Axis
Communications AB
Flash/ROM char device v2.1, (c) 1999 Axis
Communications AB
Checking flash partitions:
  /dev/flash0 at 0x80000000, size 0x10000
 Found valid partition table at 0x8001000A-0x80010056.
  /dev/flash1 at 0x80010000, size 0x1a0000
  /dev/flash2 at 0x801b0000, size 0x50000
Etrax/100 10/100MBit ethernet driver v1.4, (c) 2000
Axis Communications AB
eth0 initialized
eth0: changed MAC to 00:40:8C:CD:00:00
JFFS, version 1.0, (C) 1999, 2000  Axis Communications
AB
VFS: Mounted root (romfs filesystem) readonly.
mounting proc
Starting ping_ipset thread
Starting init...
Init starts up...
Mounting /etc
JFFS: Trying to mount device 3c:12.
JFFS: Successfully mounted device 3c:12.
Mounted /dev/flash2 on /mnt/flash ok.
##### Software version: Axis Developer Board - version
1.0.2 #####
Unpacking 512 kbyte ramdisk
Mounting ramdisk on /tmp
Mounted /dev/ram0 on /tmp ok.
usage: if ( <var> <op> <value> )
Setting up eth0 with ip 131.91.82.156 and mac
00:40:8c:46:70:3e
change IP to 0x9c525b83
eth0: changed MAC to 00:40:8C:46:70:3E
route: netmask doesn't match route address
Setting up lo with ip 127.0.0.1
change IP to 0x100007f
Default gateway is 131.91.80.1
SIOCADDRT: Network is unreachable 
Hostname is "AxisProduct"
Domainname is ""
Nameserver is ""
usage: if ( <var> <op> <value> )
Jan 01 00:01:23 AxisProduct syslogd 1.3-3: restart.
Jan  1 00:01:24 AxisProduct dnrd: osock: Couldn't
connect to 0.0.0.224
Jan  1 00:01:24 AxisProduct dnrd: osock: Couldn't
connect to any of the given srvers
boa: servername set to 131.91.82.156.
Jan  1 00:01:25 AxisProduct boa[21]: starting server
AxisProduct login: Jan  1 00:01:28 AxisProduct
sftpd[22]: sftpd $Revision: 1.67$ starting up
Sniffing /dev/ttyS0 at 115200 Baud


AxisProduct login: root
root
Password: pass

Jan  1 00:07:57 AxisProduct login: DIALUP AT ttyS2 BY
root
Jan  1 00:07:57 AxisProduct login: ROOT LOGIN ON ttyS2

Sash (version 2.2)
24# 


Thanks in Advance

regards

jai



=====
Puttamreddy, Jaideepesh
MS Computer Engineering
Florida Atlantic University
Boca Raton;FL

__________________________________________________
Do You Yahoo!?
Get personalized email addresses from Yahoo! Mail - only $35 
a year!  http://personal.mail.yahoo.com/