[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Flash-Problem / No startup



Hello!

> CONFIG_ETRAX_DEF_R_DRAM_CONFIG=1a200040
> CONFIG_ETRAX_DEF_R_DRAM_TIMING=5611

is correct.

> try boot_linux -F -p. There should be several --setreg options.

gave the following output:
Command:
etrax100boot --setreg b0000000 000095f8 --setreg b0000004 00000104 --setreg 
b000000c 1a200040 --setreg b0000008 00005611 --setreg b0000030 00001df0 
--setreg b0000038 00001ef3 --bootfile DBG2 --file fimage c0004000 --flash 
c0004000 0 200000 --jump 0

Is it possible that the RAM is defect?
The RAM was very hot one time (i think too hot).

Greetings
Markus


> It looks like the problem we had.
> Effekt: flashing worked but reboot caused hangup with both leds on
> Reason: Ram address typo
>
> took us some time to find :)
>
> walter
>
> - - - - - - - - - - - - - - Original Message - - - - - - - - - - - - - -
> From: Mikael Starvik <mikael.starvik@xxxxxxx.com>
> Subject: RE: Flash-Problem / No startup
> Date: 06/16/04 09:59
>
> try boot_linux -F -p. There should be several --setreg options.
>
> Do you run RedHat?
>
> It could be another UTF-8 problem.
>
> Try doing
> export LANG=C
> export LC_ALL=C
> and start the installation from scratch.
>
> Memory configuration of a developer board LX is
>
> CONFIG_ETRAX_DEF_R_DRAM_CONFIG=1a200040
> CONFIG_ETRAX_DEF_R_DRAM_TIMING=5611
>
> /Mikael
>
>
> -----Original Message-----
> From: Markus Wentker [mailto:markus.wentker@xxxxxxx.de]
> Sent: Wednesday, June 16, 2004 9:39 AM
> To: Mikael Starvik
> Cc: dev-etrax
> Subject: Re: Flash-Problem / No startup
>
>
> Hello!
>
> No, this was the complete DEBUG-Output.
>
> I didn't change anything when re-flashing the Devboard.
> Also made "make clean" and then "make kernel & make images"
>
> However I will check this.
>
> Where can I check the RAM Configuration?
> I found in the mailing-archiv that this is done by kernelconfig.
> What is the correct value for a DevboardLX?
>
> Many thanks in advance.
> Markus
>
> > >Here is the debugging-out from the serial-port:
> > >SET_REGISTER
> > >0xB0000038
> > >0x00001EF3
> > >PACKET_INFO
> > >0xC0004000
> > >0x00200018
> > >Checksum of file is 0x00000000
> >
> > This is not normal. There should more SET_REGISTERs. Did you cut them?
> > A failure when jumping to 0x00000000 normally indicates a RAM
> > configuration error. My first shot would be to do a complete remake
> > to be sure. Or download some other software that you know has worked
> > before.
> >
> > /Mikael
> >
> > -----Original Message-----
> > From: owner-dev-etrax@xxxxxxx.com">mailto:owner-dev-etrax@xxxxxxx.com] On
> > Behalf Of Markus Wentker
> > Sent: Tuesday, June 15, 2004 3:20 PM
> > To: dev-etrax
> > Subject: Flash-Problem / No startup
> >
> >
> > Hello!
> >
> > We have a problem with our DevboardLX.
> > Just in work it hung up and then didnīt started up again.
> > The Processor and RAM was very hot this time. Maybe the sun did the best
> > it could this time....
> >
> > We tried to flash it again, but nothing worked...
> >
> > Here is the debugging-out from the serial-port:
> > SET_REGISTER
> > 0xB0000038
> > 0x00001EF3
> > PACKET_INFO
> > 0xC0004000
> > 0x00200018
> > Checksum of file is 0x00000000
> > FLASH
> > 0xC0004000
> > 0x00000000
> > 0x00200000
> > CFI dev 0x80000000
> > No 1x CFI at 0x84000000
> > No single x16 at 0x84000000
> > No interleaved x16 at 0x84000000
> > 0x80000000: Erasing 0x00200000 bytes...done, verifying...OK
> > 0x80000000: Writing 0x00200000 bytes...verified
> >  JUMP 0x00000000
> >
> > After this the board doesnīt start. Both LEDs (the yellow and orange one)
> > light all the time.
> >
> > Iīm wondering about the Checksum of 0x0000000.
> >
> > Is there something broken on the board.
> >
> > Greetings
> > Markus