[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Flash-Problem / No startup



Hello again!

So Iīve tried a lot of things now, but everytime the same error.

Is there a way to find out whether the RAM is defect or not?

I think itīs the only possible solution, because the Devboard worked and when 
I just measured some SyncSerial-Signals it suddenly stopped...

Greetings & a thanks for all the answers
Markus


Am Mittwoch, 16. Juni 2004 11:44 schrieben Sie:
> >etrax100boot --setreg b0000000 000095f8 --setreg b0000004 00000104
> > --setreg
> >
> >b000000c 1a200040 --setreg b0000008 00005611 --setreg b0000030 00001df0
> >--setreg b0000038 00001ef3 --bootfile DBG2 --file fimage c0004000 --flash
> >c0004000 0 200000 --jump 0
>
> Correct.
>
> >Is it possible that the RAM is defect?
>
> Maybe.
>
>
>
> -----Original Message-----
> From: owner-dev-etrax@xxxxxxx.com">mailto:owner-dev-etrax@xxxxxxx.com] On Behalf
> Of Markus Wentker
> Sent: Wednesday, June 16, 2004 11:28 AM
> To: dev-etrax
> Subject: Re: Flash-Problem / No startup
>
>
> Hello!
>
> > CONFIG_ETRAX_DEF_R_DRAM_CONFIG=1a200040
> > CONFIG_ETRAX_DEF_R_DRAM_TIMING=5611
>
> is correct.
>
> > try boot_linux -F -p. There should be several --setreg options.
>
> gave the following output:
> Command:
> etrax100boot --setreg b0000000 000095f8 --setreg b0000004 00000104 --setreg
> b000000c 1a200040 --setreg b0000008 00005611 --setreg b0000030 00001df0
> --setreg b0000038 00001ef3 --bootfile DBG2 --file fimage c0004000 --flash
> c0004000 0 200000 --jump 0
>
> Is it possible that the RAM is defect?
> The RAM was very hot one time (i think too hot).
>
> Greetings
> Markus
>
> > It looks like the problem we had.
> > Effekt: flashing worked but reboot caused hangup with both leds on
> > Reason: Ram address typo
> >
> > took us some time to find :)
> >
> > walter
> >
> > - - - - - - - - - - - - - - Original Message - - - - - - - - - - - - - -
> > From: Mikael Starvik <mikael.starvik@xxxxxxx.com>
> > Subject: RE: Flash-Problem / No startup
> > Date: 06/16/04 09:59
> >
> > try boot_linux -F -p. There should be several --setreg options.
> >
> > Do you run RedHat?
> >
> > It could be another UTF-8 problem.
> >
> > Try doing
> > export LANG=C
> > export LC_ALL=C
> > and start the installation from scratch.
> >
> > Memory configuration of a developer board LX is
> >
> > CONFIG_ETRAX_DEF_R_DRAM_CONFIG=1a200040
> > CONFIG_ETRAX_DEF_R_DRAM_TIMING=5611
> >
> > /Mikael
> >
> >
> > -----Original Message-----
> > From: Markus Wentker [mailto:markus.wentker@xxxxxxx.de]
> > Sent: Wednesday, June 16, 2004 9:39 AM
> > To: Mikael Starvik
> > Cc: dev-etrax
> > Subject: Re: Flash-Problem / No startup
> >
> >
> > Hello!
> >
> > No, this was the complete DEBUG-Output.
> >
> > I didn't change anything when re-flashing the Devboard.
> > Also made "make clean" and then "make kernel & make images"
> >
> > However I will check this.
> >
> > Where can I check the RAM Configuration?
> > I found in the mailing-archiv that this is done by kernelconfig.
> > What is the correct value for a DevboardLX?
> >
> > Many thanks in advance.
> > Markus
> >
> > > >Here is the debugging-out from the serial-port:
> > > >SET_REGISTER
> > > >0xB0000038
> > > >0x00001EF3
> > > >PACKET_INFO
> > > >0xC0004000
> > > >0x00200018
> > > >Checksum of file is 0x00000000
> > >
> > > This is not normal. There should more SET_REGISTERs. Did you cut them?
> > > A failure when jumping to 0x00000000 normally indicates a RAM
> > > configuration error. My first shot would be to do a complete remake
> > > to be sure. Or download some other software that you know has worked
> > > before.
> > >
> > > /Mikael
> > >
> > > -----Original Message-----
> > > From: owner-dev-etrax@xxxxxxx.com">mailto:owner-dev-etrax@xxxxxxx.com] On
> > > Behalf Of Markus Wentker
> > > Sent: Tuesday, June 15, 2004 3:20 PM
> > > To: dev-etrax
> > > Subject: Flash-Problem / No startup
> > >
> > >
> > > Hello!
> > >
> > > We have a problem with our DevboardLX.
> > > Just in work it hung up and then didnīt started up again.
> > > The Processor and RAM was very hot this time. Maybe the sun did the
> > > best it could this time....
> > >
> > > We tried to flash it again, but nothing worked...
> > >
> > > Here is the debugging-out from the serial-port:
> > > SET_REGISTER
> > > 0xB0000038
> > > 0x00001EF3
> > > PACKET_INFO
> > > 0xC0004000
> > > 0x00200018
> > > Checksum of file is 0x00000000
> > > FLASH
> > > 0xC0004000
> > > 0x00000000
> > > 0x00200000
> > > CFI dev 0x80000000
> > > No 1x CFI at 0x84000000
> > > No single x16 at 0x84000000
> > > No interleaved x16 at 0x84000000
> > > 0x80000000: Erasing 0x00200000 bytes...done, verifying...OK
> > > 0x80000000: Writing 0x00200000 bytes...verified
> > >  JUMP 0x00000000
> > >
> > > After this the board doesnīt start. Both LEDs (the yellow and orange
>
> one)
>
> > > light all the time.
> > >
> > > Iīm wondering about the Checksum of 0x0000000.
> > >
> > > Is there something broken on the board.
> > >
> > > Greetings
> > > Markus